Link:INB Home|INB English| INB русский язык|INB العربية|INB Türkiye|INB فارسی|INB Español|INB Français|INB Português|INB Deutsch|INB 國語|INB 中文|INB 日本语|INB 한국어|INB ภาษาไทย|INB tiếng Việt||Tutorials Rhino 3D Surface Continuity (Part Two)
INB Português Fórum
BEM - vindo a indústria nativa e "boffin") Da era industrial, aqui está cheio de espírito de Luta, Ambos através Da rede espaço biológico nativo espírito "boffin" VEIO a mad labs.Casa inbforum.com, Nome Definitivo: inb-english.forumotion.com
INB Português Fórum
BEM - vindo a indústria nativa e "boffin") Da era industrial, aqui está cheio de espírito de Luta, Ambos através Da rede espaço biológico nativo espírito "boffin" VEIO a mad labs.Casa inbforum.com, Nome Definitivo: inb-english.forumotion.com
INB Português Fórum

BEM - vindo a indústria nativa e boffin) Da era industrial, aqui está cheio de espírito de Luta, Ambos através Da rede espaço biológico nativo espírito boffin VEIO a mad labs.Casa inbforum.com, Nome Definitivo: inb-english.forumotion.com


Você não está conectado. Conecte-se ou registre-se

《《《《《《《上一页INBforum   Ir para baixo

上一页INBforum》》》》》》》Ver o tópico anterior Ver o tópico seguinte Ir para baixo  Mensagem [Página 1 de 1]

1Tutorials Rhino 3D Surface Continuity (Part Two) Empty Tutorials Rhino 3D Surface Continuity (Part Two) Qua Jan 26, 2011 1:32 am

Admin

Admin
Admin
September 8, 2010
Category: 3D Modeling

This
is Part 2 of Rhino 3D Tutorial: Surface Continuity. This is an article
pertaining to surface/form modelling for industrial and product design.
Click here to go back to Part One of this article.
In Part 1, we have created a curve that is tangent to the edge of
the existing surface. Now, we need to proceed to make the curve G2
(curvature) continuous to the edge.
We can use Match Curve to bring the curve to
curvature (G2) continuity with the adjacent surface edge. Match Curve
is within the Curve Tool panel. Select Continuity as Curvature from the
Match Curve option. Note: For curves that have less than 6 control
points, the curvature at the other end of the curve to match may be
modified. The Preserve other end option prevents this modification.

Tutorials Rhino 3D Surface Continuity (Part Two) Rhinocontinuity6
From the screenshot shown above, we can see that the Curvature Graph
displays a better flow with little or no sudden break or transition.
Next, we can bring up the Adjust Curve End Bulge
tool to fine tune the curve. Make sure that the side (as indicated as 1
in the screenshot below) has Continuity = Curvature at the command
line/prompt. For the other end (indicated as 2 in the screenshot
below), in our case here, Continuity = Position is to be set. This is
because we have only created enough control points for curvature to one
end of the curve.
Tutorials Rhino 3D Surface Continuity (Part Two) Rhinocontinuity8
Once we are satisfied with this curve, we can proceed to create the
other curve to match the other surface edge. Use the same method as
described to ensure curve is curvature-matched to the edge as well. See
illustration below of the other curve.
Tutorials Rhino 3D Surface Continuity (Part Two) Rhinocontinuity91
Now, we can use a surface tool with continuity to create the
surface. In this case here, a new curve is created as shown below. The
control point is turned on to adjust the profile to give it a slight
bulge.
Tutorials Rhino 3D Surface Continuity (Part Two) Rhinocontinuity10
Next, using Surface from Network of curve, create the surface. Remember to set the Edge matching option to Curvature at the Options dialog. In this case, this is indicated as edge D. This is very important as surfaces do not automatically become curvature-matched even though the curves used to create them are.
Tutorials Rhino 3D Surface Continuity (Part Two) Rhinocontinuity11
Use the Zebra tool to evaluate the surface continuity. Zebra strips
can be used to indicate whether surfaces are position, tangent or
curvature to each other. However, we are not going to go into the
details here. Please note that the zebra tool cannot detect higher end
continuity that can be seen by a curvature graph display.
Tutorials Rhino 3D Surface Continuity (Part Two) Rhinocontinuity12
What we have illustrated here is just a simple example. If we have additional adjacent surface edges to match to, the surface from network of curve tool can provide surface continuity matching options for all sides of its boundaries.
Well, that’s all for this article. Thanks for reading Tutorials Rhino 3D Surface Continuity (Part Two) Icon_smile
About the Author: Being an industrial designer by
profession, I have done much technical modelling projects for clients
such as Razer and Creative Technology. I am proficient with
Aliasstudio, Pro-Engineer and Rhinoceros 3D.
Disclaimer: We are in no way to be held responsible if the results is not as desired by you.]

http://pt.inbforum.com

上一页INBforum   Ir para baixo

上一页INBforumVer o tópico anterior Ver o tópico seguinte Ir para o topo  Mensagem [Página 1 de 1]

Permissões neste sub-fórum
Não podes responder a tópicos

Copyright ©2009-2010 LTD Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

IT:SINGLESERVGoogle谷歌翻译TranslateFORUMSOFTLAYERGoogle谷歌广告联盟AdSenseAsia

 

Como criar um fórum | ©phpBB | Fórum gratuito de ajuda | Denunciar um abuso | Fórum grátis